Lapidary Journal Jewelry Artist: Gems, Beads, Jewelry Making and more

glass latticcino rods Ring Repair: Installing a Spring Insert
BY ALAN REVERE
Intermediate project. Eighth in a series of 12 ring repair projects.
Photos: Barry Blau.

Mrs. Mariposa has been a regular customer of your jewelry store for as long as you can remember so you are not at all surprised to see her 1 afternoon. Rather than browsing and checking out the showcases for anything she has not seen before, she asks if you can do anything to prevent her ring from sliding around her finger. Upon close observation, you can see that the ring slides over her knuckles easily enough, but when it is all the way onto her finger, it appears several sizes too large.

There are several ways to correct this problem. The most economical solution would be to add sizing beads, and the most expensive would be to use a commercial ring mechanism. You suggest that Mrs. Mariposa add a 14K gold spring insert or “butterfly” to the inside of the ring shank. This is the middle course as far as appearance and cost, and it may also be the most comfortable because the spring action is self-adjusting. It is only slightly more involved than adding beads and, in many cases, it provides far greater comfort.


TOOLBOX
  • Piece of unannealed 14k gold ribbon about 0.3-0.4mm thick and as wide as the narrowest part of the shank
  • Ring mandel about 2 sizes
  • Pair of round-nose pliers
  • Firecoat solution (powdered boric acid in alcohol)
  • Mounted soldering tweezers
  • Yellow-gold solder
  • Firesource and protective materials
  • Ball bur
  • Polished burnisher
  • Buffing wheel
  • Rouge

For information on supplies, please see the Annual Buyers' Directory.
Always ask for the MSDS (Material Safety Data Sheet) for any materials you buy, which will give you reactivity, health hazard, and safe handling data.

STEP 1.
In order for the spring material to add thickness to the inside of the ring, it may be necessary to size the ring first, depending on the fit and the width of the ring. For instance, a wide ring will fit more tightly and, therefore, needs to be sized up as much as 1/2 a size to allow for a butterfly. A thin solitaire will need to go up no more than a 1/4 of a size before installing the spring. If the ring already slips easily over the knuckle, the current size should accommodate the thickness of the spring.

STEP 2.
Determine the length of the 14K gold strip needed by measuring the interior diameter (mm) of the ring and multiplying this measurement by 1.75. This should result in a strip that covers 1/2-2/3 of the ring interior.

STEP 3.
Bend the strip over a ring mandrel that is about 2 sizes smaller than the ring. Use a pair of round-nose pliers to bend the ends of the butterfly strip outward so that they will not injure the wearer.

STEP 4.
Pre-polish the inside of the ring if needed, as well as the inside and outside of the spring.

 

STEP 5.
Before soldering, check for prior seams. Always use easy solder to attach the spring. Dip the ring in firecoat solution, set it up in mounted soldering tweezers, and then place a small piece of easy yellow-gold solder on the inside of the shank. Bring the flame to the shank and gently warm the metal. Apply just enough heat to permit the solder to melt onto the surface, but do not allow the solder to flow completely.

As an alternative, you can make a 4mm-long indentation with a ball bur on the inside of the shank where the spring will be attached. Place a piece of solder in the depression, melt it, and then file flush before attaching the spring. The advantage to this method is that it eliminates excess solder that might flow up the sides of the spring solder.

STEP 6.
When the solder is melted onto the shank, place the firecoated and fluxed spring in position and hold it there with a pair of soldering tweezers. Now heat the assembly with an unusually hot flame as you sweat solder the pieces together. Watch for signs that the solder has flowed from the ring to the spring. Do not overheat.

STEP 7.
Make sure that the edges of the spring are smooth and rounded so that they cannot injure the wearer. Check the fit and symmetry. Test to see if the spring holds its shape under pressure. If it doesn't, it should be hardened by rubbing the surface with a polished burnisher.

STEP 8.
Touch up the spring with a buffing wheel, clean, and then use rouge to apply a high polish as needed. The ring should now slide over the knuckle without too much effort, sit comfortably, and remain right side up.

Alan Revere is a German-trained master goldsmith, an award-winning designer, and a jewelry educator, author, and lecturer. He is the director of the Revere Academy of Jewelry Arts in San Francisco.

 

This project is adapted with permission from Ring Repair.



Choose from 2 Exciting Offers
Lapidary Journal Jewelry Artist Magazine

BEST
DEAL

We have a special internet offer just for you. Subscribe to one year of Jewelry Artist, PAY NOW and receive 2 extra issues (14 issues in all) for FREE! You save over 64% off the newsstand price.

Yes, send me 14 issues for only $29.95!

Jewelry Artist Best Deal
U.S. funds only. Add $15/yr for Canadian, $25/yr for Int’l
OR

Send me a FREE trial issue of Jewelry Artist. I'll
get a one-year subscription (12 issues) for
only $29.95 —that's a savings of over 59% off
the newsstand price! If I'm not completely satisfied,
I can keep my FREE issue and return the bill
marked "cancel" and owe nothing.

Just fill out this form—it's Risk Free!

U.S. funds only. Add $15/yr for Canadian, $25/yr for Int’l
First Name
 Last Name
Street 1
 Street 2
City
 State
Zip
 Country
Email
TRIAL SUBSCRIPTION

Pay nothing now

________________________________________________________________

Feature Stories & Artist Profiles | Step-by-Step Projects & Workshops | Technique Articles | Business Articles | New Products | News, Conferences, & Deadlines | Take our Reader Survey

Articles & Workshops | Bead Fest | Jewelry Classes | Show Calendar | Search for Products & Suppliers | Classified Ad Deals | Advertising Rates & Information | Media Reviews | Store - Books & Back Issues | Contact Us | Links | Site Map

About Us | Subscribe to Lapidary Journal Jewelry Artist | Subscription Customer Service/Account Lookup

Contact us.
All content on this site © Lapidary Journal Jewelry Artist /Interweave Press.
If you have any questions or problems regarding this site, please e-mail our site editor.